mining pump

	The frame plate liners for AH series pumps have replaceable wear-resistant rubber liners. The impellers are made of natural rubber liners. It has nearly the same constructer with AHM. The type of AH pumps are also using for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments . It is suitable for the corrosive slurry usually. In some ore dressing, some bigger AH series pump also would be used to transport the fine ore or tailings with weak abrasion.
	The type of AHM pumps are using for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc. For example: Coal wash processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station.
	Type ALM(R) pumps are cantilevered, horizontal, centrifugal, slurry pumps. Its adopted high speed operating and so they have small volumes saving floor area. The frame plates have changeable, wear-resistant, metal liners or rubber liners and the impellers are made of wear-resistant metal or rubber (Rubber for frame plates, impellers of pumps with discharge Dia. (mm) above 550mm.)The discharge position as request may be rotated 8 different angles at internal of 45 degrees for installation and application. They are suitable for delivering low abrasive, low-density slurries for metallurgical, mining, coal and build material departments. The shaft seal is adopted both gland seal and centrifugal seal.
	Series AMM pumps are cantilevered, horizontal, centrifugal, slurry pumps. Series AMM pumps are adopted high speed operating and so they have small volumes saving floor area. The discharge position by request may be rotated 8 different angles at internal of 45 degrees for installation and application. They are suitable for delivering middle abrasive, middle-density slurries for metallurgical, mining, coal and build material departments. The shaft seal is adopted both gland seal and centrifugal seal.
	AS(G) series gravel pumps are horizontal and single-casing centrifugal pumps. The type AS (G) pumps are of high-head ones. Construction of this pump is of single casing connected by means of clamp bands and wide wet-passage. The wet-parts are made of Ni-hard and high-chrome wear-resistant alloys. The discharge direction of pump can be oriented in any direction of 360. This type of pump owns the advantages of easy installation, good performance of NPSH and wear-resistance. Gravel pumps are designed for continuously handling the most difficult higher abrasive slurries, which contain too big solids, to be pumped by common pumps. They are suitable for delivering slurries in mining, explosive -sludge in metal melting, dredging in dredger and course of rivers, and other fields.
	In order to meet the requirements on the development of mining, the power plant, metallurgy and coal industries, our works has designed and developed Series AZG(S) Generation Slurry Pump with large capacity, high head, multi-stage with experience of slurry pump design and manufacture for many years, and absorbing the research results of advanced technology from home and abroad. It is widely used for handling the mixture of abrasive and corrosive solids in power, metallurgy, coal, building materials, chemical industry departments, especially for removing ash and sludge in power plant.
	The AZJ series slurry pumps are designed as single-stage, single-suction centrifugal pumps. They are classified into the horizontal type (AZJ type) and vertical type (AZJV type) according to construction. The pumps are innovative in both hydraulic and structural design. The wet parts are made from high-chrome alloy with high wear-resistance. They are of energy- saving, high efficiency, little vibration, low noise, long service, lightweight, reliable operation and easy maintenance. The AZJ series slurry pumps are widely used in power plant, metallurgical, mining, coal, etc. which are suitable for handling abrasive and corrosive slurries with maximum concentrations of wt.45% (ash) and wt.60% (ore) such as the fine ore and tailings in mining, removing ash in power plant and delivering coal tailings. The pumps can be operated in series according to special requirements.